The E4P is no longer available for purchase.
The E4P is no longer available for purchase, and has been replaced by our recently released E4T. The E4T is a redesigned, enhanced version of the E4P, and is already available for purchase.
E4P Product Description
The E4P miniature reflective encoder is designed to provide digital quadrature encoder feedback for high-volume applications with limited space constraints. The E4P version utilizes an innovative, patented push-on encoder disk that accepts shaft diameters of 2mm to .250 in.
The E4P reflective encoder is the leader for high-quality OEM applications, but the E4 is the ideal choice when a set-screw encoder disk encoder is required (see the E4 page).
The E4P miniature encoder base provides mounting holes for two #3-48, length 1/4 in. or two M2.5x.45mm, length 6mm screws on a .586 in. bolt circle. When mounting holes are not available, a pre-applied transfer adhesive (with peel-off backing) is available for "stick-on" mounting.
The encoder cover is easily snapped onto the base and is embossed with the connector pin-out.
The E4P reflective series encoder can be connected using a (high retention 4-conductor snap-in polarized 1.25mm pitch) connector. Mating cables and connectors (see the Cables/Connectors web page) are not included and are available separately.
Product Specifications
View here or download the specifications
ENVIRONMENTAL
| PARAMETER |
VALUE |
UNITS |
| Vibration (5Hz to 2kHz) |
20 |
G |
| Max. Relative Humidity |
90 |
% |
| Storage Temperature |
-40 to 100 |
C |
| Operating Temperature |
-20 to 100 |
C |
Electrostatic Discharge, IEC 61000-4-2
Single-ended (S-option)
Differential (D-option) |
± 8
± 15 |
kV |
MECHANICAL
| PARAMETER |
VALUE |
UNITS |
| Max. Shaft Axial Play |
± .020 |
in. |
| Max. Off-axis Mounting Tolerance |
± .010 |
in. |
| Max. Acceleration |
250000 |
rad/sec² |
Mounting Screw Size
Default (D-option base)
Metric (M-option base) |
#3-48 x 1/4"
M2.5x.45mm, length 6mm |
|
| Screw Bolt Circle Diameter |
.586 ±.002 |
in. |
| Axial Length of Codewheel |
.270 |
in. |
| Required Shaft Length (1) |
.375 to .395 |
in. |
| Mounting Screw Torque |
2-3 |
in-lbs |
| Technical Bulletin TB1001 - Shaft and Bore Tolerances |
Download |
(1) Includes axial play.
SINGLE-ENDED ELECTRICAL
| SPECIFICATIONS |
MIN. |
TYP. |
MAX. |
UNITS |
NOTES |
| Supply Voltage |
4.5 |
5.0 |
5.5 |
V |
|
| Supply Current |
|
21 |
27 |
mA |
no load |
| Low-level Output |
|
|
0.4 |
V |
IOL = 6 mA |
| High-level Output |
2.4 |
|
|
V |
IOH = -1 mA |
| Rise Time |
|
500 |
|
ns |
CL = 25 pF, RL = 2.7 kΩ |
| Fall Time |
|
100 |
|
ns |
|
DIFFERENTIAL ELECTRICAL
| SPECIFICATIONS |
MIN. |
TYP. |
MAX. |
UNITS |
NOTES |
| Supply Voltage |
4.5 |
5.0 |
5.5 |
V |
|
| Supply Current |
|
23 |
29 |
mA |
no load |
| Single-Ended Output Voltage High |
4.75 |
5.0 |
|
V |
Min. @ 25mA load, Typ. @ no load |
| Single-Ended Output Voltage Low |
|
0.25 |
0.60 |
V |
Typ. @ no load, Max. @ 4.5mA load |
| Differential Output Voltage |
3.0 |
3.8 |
|
V |
RL = 100 ohm |
| Differential Output Rise/Fall Time |
|
|
1300 |
ns |
|
PHASE RELATIONSHIP
| PARAMETER |
TYP. |
MAX. |
UNITS |
| Symmetry, S |
180 ± 16 |
180 ± 75 |
electrical degrees |
| Quadrature Delay, Q |
90 ± 10 |
90 ± 60 |
electrical degrees |
(1) A leads B for clockwise shaft rotation, B leads A for counterclockwise shaft rotation viewed from the cover/label side of the encoder.
(2) Typical values represent the encoder performance at typical mounting alignment, whereas the maximum values represent the encoder performance across the range of recommended mounting tolerance.
PIN-OUT
| 4-PIN SINGLE-ENDED (1) |
6-PIN DIFFERENTIAL (2) |
| Pin |
Description |
Pin |
Description |
| 1 |
+5VDC power |
1 |
Ground |
| 2 |
A channel |
2 |
A channel |
| 3 |
Ground |
3 |
A- channel |
| 4 |
B channel |
4 |
+5VDC power |
| |
|
5 |
B channel |
| |
|
6 |
B- channel |
(1) 4-pin single-ended mating connector is CON-MIC4
(2) 6-pin differential mating connector is CON-MIC6
OPTIONS
H-OPTION (HOLE IN COVER)
The H-option adds a hole in the cover for the shaft to pass through:
- For shaft diameters of 1.5mm to 1/8", a 0.170" hole is supplied.
- For shaft diameters of 5/32" to 1/4", a 0.295" hole is supplied.
M-OPTION (METRIC MOUNTING SCREWS)
Provides alternate metric M2.5x.45mm, length 6mm screws. When M-option is NOT specified the default is #3-48 x 1/4" screws.
T-OPTION (TRANSFER ADHESIVE)
When mounting holes are not available, a pre-applied transfer adhesive (with peel-off backing) is available for "stick-on" mounting. Use the centering tool (above) to position the base. T-option specifies transfer adhesive.
Before installation, cleaning the mounting surface with alcohol is recommended to remove dust and oil.
ACCESSORIES
1. Centering Tool
The centering tool is only included with the -3 packaging option. It has to be ordered separately for other package options.
Part #: MCTOOL - (Shaft Diameter)
Description: This reusable tool provides a simple method for accurately centering the E4P base onto the shaft. A centering tool is highly recommended when using the T-option transfer adhesive.
2. Spacer Tool
A spacer tool is included for all packaging options.
Part #: SPACER-E4P
Description: This reusable tool is used to properly space the codewheel from the encoder.
PRODUCT CHANGE NOTIFICATIONS
| Title |
Date |
Description |
Download |
| E4, E4P, S4 - PCN 5741 |
05/09/2016 |
As part of our on-going product lifecycle management process, we have identified products that will be transitioned to an "End-of-Life" status. Products targeted for end-of-life may be available for a last time buy option prior to being made obsolete, however quantities are limited, and special requirements may apply. |
Download |
| E4 - E4P - S4 Update - PCN 1014 |
11/29/2011 |
We have modified the E4, E4P and S4 product lines in order to improve the performance and durability of the encoder. Changes include new molds for the plastic base and cover parts with an over-molded bushing in the S4 base, a new SMT connector (compatible with current mating connector)and a modified PCB profile to accommodate the new connector and plastic part modifications. |
Download |
Additional Information
Product Notes
-
Cables and connectors are not included and must be ordered separately.
-
US Digital® warrants its products against defects in materials and workmanship for two years. See complete warranty for details.
Datasheets
Related
Feedback
US Digital's mission is a commitment to quality and constant improvement. If you find an error to a product on this page, please let us know!
